root@driver:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.165-v8 (root@kernel-build) (aarch64-linux-gnu-gcc (Linaro GCC 7.5-2019.12) 7.5.0, GNU ld (Linaro_Binutils-2019.12) 2.28.2.20170706) #6 SMP Thu Nov 21 20:07:03 CST 2024 [ 0.000000] Machine model: smartlogic,ucp2 [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000f0000000, size 192 MiB [ 0.000000] OF: reserved mem: initialized node memory@0xb0000000, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000003ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x00000000b7ffffff] [ 0.000000] node 0: [mem 0x00000000b8000000-0x00000003ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x00000003ffffffff] [ 0.000000] On node 0 totalpages: 4128768 [ 0.000000] DMA zone: 15360 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 983040 pages, LIFO batch:63 [ 0.000000] Normal zone: 49152 pages used for memmap [ 0.000000] Normal zone: 3145728 pages, LIFO batch:63 [ 0.000000] percpu: Embedded 22 pages/cpu s49304 r8192 d32616 u90112 [ 0.000000] pcpu-alloc: s49304 r8192 d32616 u90112 alloc=22*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 4064256 [ 0.000000] Kernel command line: console=ttyS0,115200n8 coherent_pool=32M root=/dev/mmcblk0p3 rootwait rw hugepagesz=1G default_hugepagesz=1G hugepages=0 isolcpus=1-7 nohz_full=1-7 rcu_nocbs=1-7 [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000ec000000-0x00000000f0000000] (64MB) [ 0.000000] Memory: 13197468K/16515072K available (8446K kernel code, 1100K rwdata, 2940K rodata, 1728K init, 586K bss, 3120996K reserved, 196608K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001900000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] NO_HZ: Full dynticks CPUs: 1-7. [ 0.000000] rcu: Offload RCU callbacks from CPUs: 1-7. [ 0.000000] SCRG reg base is ffffffc010f00000 [ 0.000000] CCRG reg base is ffffffc010f18000 [ 0.000000] arch_timer: cp15 timer(s) running at 50.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns [ 0.000001] sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns [ 0.000105] Console: colour dummy device 80x25 [ 0.000122] Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=50000) [ 0.000129] pid_max: default: 32768 minimum: 301 [ 0.000228] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000279] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000930] rcu: Hierarchical SRCU implementation. [ 0.001387] smp: Bringing up secondary CPUs ... [ 0.001593] Detected PIPT I-cache on CPU1 [ 0.001598] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000002faf080, CPU1: 0x00000000000000 [ 0.001608] CPU features: Unsupported CPU feature variation detected. [ 0.001615] GICv3: CPU1: found redistributor 1 region 0:0x0000000001920000 [ 0.001631] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.001831] Detected PIPT I-cache on CPU2 [ 0.001835] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000002faf080, CPU2: 0x00000000000000 [ 0.001844] GICv3: CPU2: found redistributor 2 region 0:0x0000000001940000 [ 0.001854] CPU2: Booted secondary processor 0x0000000002 [0x410fd083] [ 0.002058] Detected PIPT I-cache on CPU3 [ 0.002062] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000002faf080, CPU3: 0x00000000000000 [ 0.002071] GICv3: CPU3: found redistributor 3 region 0:0x0000000001960000 [ 0.002081] CPU3: Booted secondary processor 0x0000000003 [0x410fd083] [ 0.002303] Detected PIPT I-cache on CPU4 [ 0.002307] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000002faf080, CPU4: 0x00000000000000 [ 0.002320] GICv3: CPU4: found redistributor 100 region 0:0x0000000001980000 [ 0.002334] CPU4: Booted secondary processor 0x0000000100 [0x410fd083] [ 0.002536] Detected PIPT I-cache on CPU5 [ 0.002539] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000002faf080, CPU5: 0x00000000000000 [ 0.002549] GICv3: CPU5: found redistributor 101 region 0:0x00000000019a0000 [ 0.002559] CPU5: Booted secondary processor 0x0000000101 [0x410fd083] [ 0.002752] Detected PIPT I-cache on CPU6 [ 0.002755] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000002faf080, CPU6: 0x00000000000000 [ 0.002765] GICv3: CPU6: found redistributor 102 region 0:0x00000000019c0000 [ 0.002775] CPU6: Booted secondary processor 0x0000000102 [0x410fd083] [ 0.002967] Detected PIPT I-cache on CPU7 [ 0.002971] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000002faf080, CPU7: 0x00000000000000 [ 0.002980] GICv3: CPU7: found redistributor 103 region 0:0x00000000019e0000 [ 0.002990] CPU7: Booted secondary processor 0x0000000103 [0x410fd083] [ 0.003026] smp: Brought up 1 node, 8 CPUs [ 0.003057] SMP: Total of 8 processors activated. [ 0.003061] CPU features: detected: 32-bit EL0 Support [ 0.003064] CPU features: detected: CRC32 instructions [ 0.003098] CPU: All CPU(s) started at EL1 [ 0.003113] alternatives: patching kernel code [ 0.004453] devtmpfs: initialized [ 0.006291] Registered cp15_barrier emulation handler [ 0.006301] Registered setend emulation handler [ 0.006305] KASLR disabled due to lack of seed [ 0.006362] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.006369] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.007794] pinctrl core: initialized pinctrl subsystem [ 0.007865] ************************************************************* [ 0.007868] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.007870] ** ** [ 0.007873] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** [ 0.007875] ** ** [ 0.007877] ** This means that this kernel is built to expose internal ** [ 0.007880] ** IOMMU data structures, which may compromise security on ** [ 0.007882] ** your system. ** [ 0.007884] ** ** [ 0.007887] ** If you see this message and you are not debugging the ** [ 0.007889] ** kernel, report this immediately to your vendor! ** [ 0.007891] ** ** [ 0.007893] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.007895] ************************************************************* [ 0.008133] NET: Registered protocol family 16 [ 0.012284] DMA: preallocated 32768 KiB GFP_KERNEL pool for atomic allocations [ 0.016104] DMA: preallocated 32768 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.019937] DMA: preallocated 32768 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.020176] cpuidle: using governor menu [ 0.020242] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.020310] ASID allocator initialised with 65536 entries [ 0.027135] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.027141] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.027145] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.027148] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.028171] iommu: Default domain type: Translated [ 0.028219] arm-v7s io-pgtable: self test ok [ 0.028223] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 32 [ 0.028262] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 36 [ 0.028284] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 40 [ 0.028314] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 42 [ 0.028354] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 44 [ 0.028380] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 48 [ 0.028406] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 32 [ 0.028434] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 36 [ 0.028474] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 40 [ 0.028514] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 42 [ 0.028554] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 44 [ 0.028594] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 48 [ 0.028657] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 32 [ 0.028750] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 36 [ 0.028833] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 40 [ 0.028926] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 42 [ 0.029070] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 44 [ 0.029205] arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 48 [ 0.029336] arm-lpae io-pgtable: selftest: completed with 18 PASS 0 FAIL [ 0.029383] vgaarb: loaded [ 0.029480] SCSI subsystem initialized [ 0.029541] usbcore: registered new interface driver usbfs [ 0.029554] usbcore: registered new interface driver hub [ 0.029569] usbcore: registered new device driver usb [ 0.029724] jesd204: found 0 devices and 0 topologies [ 0.029731] pps_core: LinuxPPS API ver. 1 registered [ 0.029734] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.029740] PTP clock support registered [ 0.030085] clocksource: Switched to clocksource arch_sys_counter [ 0.030177] FS-Cache: Loaded [ 0.030267] CacheFiles: Loaded [ 0.032093] NET: Registered protocol family 2 [ 0.032543] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.035993] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.036029] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.036351] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.036632] TCP: Hash tables configured (established 131072 bind 65536) [ 0.036713] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.036766] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.036885] NET: Registered protocol family 1 [ 0.036896] PCI: CLS 0 bytes, default 64 [ 0.037744] Initialise system trusted keyrings [ 0.037802] workingset: timestamp_bits=62 max_order=22 bucket_order=0 [ 0.039575] fuse: init (API version 7.32) [ 0.039650] 9p: Installing v9fs 9p2000 file system support [ 0.039674] FS-Cache: Netfs '9p' registered for caching [ 0.061584] Key type asymmetric registered [ 0.061588] Asymmetric key parser 'x509' registered [ 0.061603] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.061607] io scheduler mq-deadline registered [ 0.061610] io scheduler kyber registered [ 0.061863] pinctrl-ucp2 pinctrl@04458000: ucp2 pintrl probe ok! [ 0.061934] gpio-dwapb 4450000.gpio: no IRQ for port0 [ 0.062478] gpio-dwapb 4d10000.gpio: no IRQ for port0 [ 0.063117] dw_axi_dmac_platform 4540000.dma-controller: DesignWare AXI DMA Controller, 8 channels [ 0.063157] dw_axi_dmac_platform: probe of 4d38000.dma-controller failed with error -2 [ 0.063265] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.064775] printk: console [ttyS0] disabled [ 0.064800] 4440000.serial: ttyS0 at MMIO 0x4440000 (irq = 13, base_baud = 3125000) is a 16550A [ 1.230222] printk: console [ttyS0] enabled [ 1.234664] 4d00000.serial: ttyS2 at MMIO 0x4d00000 (irq = 14, base_baud = 3125000) is a 16550A [ 1.243768] arm-smmu 42b8000.iommu: probing hardware configuration... [ 1.250184] arm-smmu 42b8000.iommu: SMMUv2 with: [ 1.254779] arm-smmu 42b8000.iommu: stage 1 translation [ 1.260066] arm-smmu 42b8000.iommu: stage 2 translation [ 1.265351] arm-smmu 42b8000.iommu: nested translation [ 1.270550] arm-smmu 42b8000.iommu: non-coherent table walk [ 1.276181] arm-smmu 42b8000.iommu: (IDR0.CTTW overridden by FW configuration) [ 1.283455] arm-smmu 42b8000.iommu: stream matching with 32 register groups [ 1.290470] arm-smmu 42b8000.iommu: 32 context banks (0 stage-2 only) [ 1.296967] arm-smmu 42b8000.iommu: Supported page sizes: 0x61311000 [ 1.303378] arm-smmu 42b8000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.309786] arm-smmu 42b8000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.317276] brd: module loaded [ 1.321927] loop: module loaded [ 1.325848] phc@0 enforce active low on chipselect handle [ 1.331842] tun: Universal TUN/TAP device driver, 1.6 [ 1.337186] VFIO - User Level meta-driver version: 0.3 [ 1.342628] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.349132] ehci-pci: EHCI PCI platform driver [ 1.353564] ehci-platform: EHCI generic platform driver [ 1.358802] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.364955] ohci-pci: OHCI PCI platform driver [ 1.369384] ohci-platform: OHCI generic platform driver [ 1.374618] uhci_hcd: USB Universal Host Controller Interface driver [ 1.380979] usbcore: registered new interface driver usb-storage [ 1.386963] i2c /dev entries driver [ 1.390501] uvp4008-pvt 4708000.pvt: ucp4008 pvt probe enter [ 1.396152] uvp4008-pvt 4708000.pvt: ucp4008 pvt interrupt number is 20 [ 1.402763] uvp4008-pvt 4708000.pvt: init ucp4008 pvt success [ 1.408512] uvp4008-pvt 4708000.pvt: ucp4008 pvt probe leave [ 1.414257] dw_wdt 4400000.watchdog: No valid TOPs array specified [ 1.420604] dw_wdt 4408000.watchdog: No valid TOPs array specified [ 1.427142] sdhci: Secure Digital Host Controller Interface driver [ 1.433293] sdhci: Copyright(c) Pierre Ossman [ 1.437628] Synopsys Designware Multimedia Card Interface Driver [ 1.443670] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.449344] pinctrl-ucp2 pinctrl@04458000: pin PD5 already requested by 4438000.spi; cannot claim for leds [ 1.458952] pinctrl-ucp2 pinctrl@04458000: pin-50 (leds) status -22 [ 1.465189] pinctrl-ucp2 pinctrl@04458000: could not request pin 50 (PD5) from group PD5 on device pinctrl-ucp2 [ 1.475313] leds-gpio leds: Error applying setting, reverse things back [ 1.481899] leds-gpio: probe of leds failed with error -22 [ 1.487380] hid: raw HID events driver (C) Jiri Kosina [ 1.492523] usbcore: registered new interface driver usbhid [ 1.498067] usbhid: USB HID core driver [ 1.501995] dw_mmc_smartlogic 1a60000.mmcsd: sdvol-gpios parsed OK [ 1.508259] dw_mmc_smartlogic 1a60000.mmcsd: sdmmc tuning clock 500000000Hz [ 1.515286] dw_mmc_smartlogic 1a60000.mmcsd: sdmmc bus clock 125000000Hz [ 1.522089] Initializing XFRM netlink socket [ 1.526343] NET: Registered protocol family 17 [ 1.530790] sctp: Hash tables configured (bind 256/256) [ 1.536085] 9pnet: Installing 9P2000 support [ 1.540413] dw_mmc_smartlogic 1a60000.mmcsd: IDMAC supports 32-bit address mode. [ 1.547787] dw_mmc_smartlogic 1a60000.mmcsd: Using internal DMA controller. [ 1.554717] dw_mmc_smartlogic 1a60000.mmcsd: Version ID is 250a [ 1.560621] dw_mmc_smartlogic 1a60000.mmcsd: DW MMC controller at irq 36,32 bit host data width,512 deep fifo [ 1.570533] mmc_host mmc0: card is non-removable. [ 1.575283] Loading compiled-in X.509 certificates [ 1.583911] dw_mmc_smartlogic 1a60000.mmcsd: emmc not support switch to 3v [ 1.590868] at24 0-0056: 131072 byte 24c1024 EEPROM, writable, 1 bytes/write [ 1.598209] dw_mmc_smartlogic 1a60000.mmcsd: sdmmc card switch to 1.8v [ 1.604799] pca954x 1-0070: probe failed [ 1.608865] printk: console [netcon0] enabled [ 1.613203] netconsole: network logging started [ 1.617902] dw-apb-uart 4440000.serial: forbid DMA for kernel console [ 1.624336] mmc_host mmc0: Bus speed (slot 0) = 125000000Hz (slot req 400000Hz, actual 398089HZ div = 157) [ 1.646261] Waiting for root device /dev/mmcblk0p3... [ 1.729007] dw_mmc_smartlogic 1a60000.mmcsd: sdmmc card switch to 1.8v [ 1.738224] mmc_host mmc0: Bus speed (slot 0) = 125000000Hz (slot req 52000000Hz, actual 31250000HZ div = 2) [ 1.748021] mmc_host mmc0: Bus speed (slot 0) = 125000000Hz (slot req 70000000Hz, actual 62500000HZ div = 1) [ 1.758258] dw_mmc_smartlogic 1a60000.mmcsd: config sdmmc tuning rxdly 8 [ 1.765178] mmc0: new HS200 MMC card at address 0001 [ 1.770352] mmcblk0: mmc0:0001 S0J59X 119 GiB [ 1.774919] mmcblk0boot0: mmc0:0001 S0J59X partition 1 31.5 MiB [ 1.780951] mmcblk0boot1: mmc0:0001 S0J59X partition 2 31.5 MiB [ 1.786902] mmcblk0rpmb: mmc0:0001 S0J59X partition 3 4.00 MiB, chardev (245:0) [ 1.796158] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 p8 > [ 2.025834] EXT4-fs (mmcblk0p3): 1 orphan inode deleted [ 2.031043] EXT4-fs (mmcblk0p3): recovery complete [ 2.041843] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 2.049918] VFS: Mounted root (ext4 filesystem) on device 179:3. [ 2.056469] devtmpfs: mounted [ 2.059776] Freeing unused kernel memory: 1728K [ 2.064368] Run /sbin/init as init process [ 2.068447] with arguments: [ 2.068449] /sbin/init [ 2.068451] with environment: [ 2.068454] HOME=/ [ 2.068455] TERM=linux [ 2.310388] systemd[1]: System time before build time, advancing clock. [ 2.338991] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 2.360367] systemd[1]: Detected architecture arm64. [ 2.382470] systemd[1]: Set hostname to . [ 2.549557] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 2.566530] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 2.643812] systemd[1]: Configuration file /etc/systemd/system/evb_boot.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.668203] random: systemd: uninitialized urandom read (16 bytes read) [ 2.677310] random: systemd: uninitialized urandom read (16 bytes read) [ 2.684025] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 2.699123] random: systemd: uninitialized urandom read (16 bytes read) [ 2.705790] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 2.724125] systemd[1]: Reached target Remote File Systems. [ 2.738656] systemd[1]: Created slice system-getty.slice. [ 3.141772] systemd-journald[135]: Received request to flush runtime journal from PID 1 [ 3.672562] random: systemd: uninitialized urandom read (16 bytes read) [ 3.688198] random: systemd: uninitialized urandom read (16 bytes read) [ 3.722353] random: systemd: uninitialized urandom read (16 bytes read) [ 4.198564] EXT4-fs (mmcblk0p1): recovery complete [ 4.203351] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.453224] EXT4-fs (mmcblk0p5): recovery complete [ 4.458006] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) [ 4.629787] EXT4-fs (mmcblk0p6): recovery complete [ 4.634572] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [ 4.700086] random: crng init done [ 4.703480] random: 229 urandom warning(s) missed due to ratelimiting [ 4.800334] EXT4-fs (mmcblk0p7): recovery complete [ 4.805117] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null) [ 4.876640] ptp_idtcm: loading out-of-tree module taints kernel. [ 4.883453] get GPIO473 [ 5.001495] idtcm spi2.0: 4.8.7, Id: 0x4002 HW Rev: 5 OTP Config Select: 0 [ 5.113159] idtcm spi2.0: Invalid TOD mask 0x00 [ 5.453781] sh (286): drop_caches: 3 [ 6.166107] idtcm spi2.0: PLL2 registered as ptp0 [ 6.225630] dwc-eth-dwmac 1a40000.ethernet0: get iommus reg 0x456003c [ 6.232072] dwc-eth-dwmac 1a40000.ethernet0: Adding to iommu group 0 [ 6.238520] dwc-eth-dwmac 1a40000.ethernet0: plat->bus_id = 0x0 [ 6.244525] dwc-eth-dwmac 1a40000.ethernet0: Cannot get CSR clock [ 6.250596] dwc-eth-dwmac 1a40000.ethernet0: PTP rate 125000000 [ 6.256490] dwc-eth-dwmac 1a40000.ethernet0: no reset control found [ 6.262727] probe data->bus_id = 0x0 [ 6.266372] dwc-eth-dwmac 1a40000.ethernet0: gmac tuning val set to 0x303 [ 6.273214] dwc-eth-dwmac 1a40000.ethernet0: smartlogic_eqos_probe OK [ 6.283159] dwc-eth-dwmac 1a40000.ethernet0: User ID: 0x10, Synopsys ID: 0x51 [ 6.290273] dwc-eth-dwmac 1a40000.ethernet0: DWMAC4/5 [ 6.295395] dwc-eth-dwmac 1a40000.ethernet0: DMA HW capability register supported [ 6.302843] dwc-eth-dwmac 1a40000.ethernet0: RX Checksum Offload Engine supported [ 6.310289] dwc-eth-dwmac 1a40000.ethernet0: TX Checksum insertion supported [ 6.317304] dwc-eth-dwmac 1a40000.ethernet0: Wake-Up On Lan supported [ 6.323748] dwc-eth-dwmac 1a40000.ethernet0: TSO supported [ 6.329209] dwc-eth-dwmac 1a40000.ethernet0: Enable RX Mitigation via HW Watchdog Timer [ 6.337176] dwc-eth-dwmac 1a40000.ethernet0: device MAC address f2:d3:18:ea:2a:ca [ 6.344623] dwc-eth-dwmac 1a40000.ethernet0: Enabled Flow TC (entries=5) [ 6.351292] dwc-eth-dwmac 1a40000.ethernet0: TSO feature enabled [ 6.357274] dwc-eth-dwmac 1a40000.ethernet0: Using 40 bits DMA width [ 6.363816] [Firmware Warn]: /soc/ethernet0@01a40000/mdio0/ethernet-phy@0: Whitelisted compatible string. Please remove [ 6.519602] dwc-eth-dwmac 8524000.ethernet2: plat->bus_id = 0x2 [ 6.525607] dwc-eth-dwmac 8524000.ethernet2: Cannot get CSR clock [ 6.531681] dwc-eth-dwmac 8524000.ethernet2: PTP uses main clock [ 6.537660] dwc-eth-dwmac 8524000.ethernet2: no reset control found [ 6.543897] probe data->bus_id = 0x2 [ 6.547543] dwc-eth-dwmac 8524000.ethernet2: gmac tuning val set to 0x101 [ 6.554384] dwc-eth-dwmac 8524000.ethernet2: smartlogic_eqos_probe OK [ 6.568685] dwc-eth-dwmac 8524000.ethernet2: User ID: 0x10, Synopsys ID: 0x51 [ 6.575804] dwc-eth-dwmac 8524000.ethernet2: DWMAC4/5 [ 6.580928] dwc-eth-dwmac 8524000.ethernet2: DMA HW capability register supported [ 6.588376] dwc-eth-dwmac 8524000.ethernet2: RX Checksum Offload Engine supported [ 6.595823] dwc-eth-dwmac 8524000.ethernet2: TX Checksum insertion supported [ 6.602837] dwc-eth-dwmac 8524000.ethernet2: TSO supported [ 6.608295] dwc-eth-dwmac 8524000.ethernet2: Enable RX Mitigation via HW Watchdog Timer [ 6.616263] dwc-eth-dwmac 8524000.ethernet2: device MAC address c2:14:f9:f2:be:66 [ 6.623710] dwc-eth-dwmac 8524000.ethernet2: TSO feature enabled [ 6.629688] dwc-eth-dwmac 8524000.ethernet2: Using 40 bits DMA width [ 6.636385] dwc-eth-dwmac 9090000.ethernet3: get iommus reg 0x91d00d8 [ 6.652231] dwc-eth-dwmac 9090000.ethernet3: Adding to iommu group 1 [ 6.658711] dwc-eth-dwmac 9090000.ethernet3: plat->bus_id = 0x3 [ 6.664738] dwc-eth-dwmac 9090000.ethernet3: Cannot get CSR clock [ 6.670811] dwc-eth-dwmac 9090000.ethernet3: PTP rate 125000000 [ 6.676703] dwc-eth-dwmac 9090000.ethernet3: no reset control found [ 6.682960] disable pcie connect [ 6.686265] disable mpll [ 6.688873] wait sram_load success [ 6.701152] disable tx and rx reset [ 6.704709] wait ack down. [ 6.907501] goto P0 [ 6.909677] wait ack done [ 7.012377] disable req [ 7.014897] wait ack down [ 7.117511] check pma rx sigdet [ 7.120722] Initializing pcs core [ 7.126628] dwc-eth-dwmac 9090000.ethernet3: smartlogic_tmac_probe OK [ 7.137912] dwc-eth-dwmac 9090000.ethernet3: User ID: 0x27, Synopsys ID: 0x20 [ 7.145033] dwc-eth-dwmac 9090000.ethernet3: XLGMAC [ 7.149982] dwc-eth-dwmac 9090000.ethernet3: DMA HW capability register supported [ 7.157429] dwc-eth-dwmac 9090000.ethernet3: RX Checksum Offload Engine supported [ 7.164876] dwc-eth-dwmac 9090000.ethernet3: COE Type 1 [ 7.170078] dwc-eth-dwmac 9090000.ethernet3: TX Checksum insertion supported [ 7.177093] dwc-eth-dwmac 9090000.ethernet3: Wake-Up On Lan supported [ 7.183543] dwc-eth-dwmac 9090000.ethernet3: TSO supported [ 7.189005] dwc-eth-dwmac 9090000.ethernet3: Enable RX Mitigation via HW Watchdog Timer [ 7.196973] dwc-eth-dwmac 9090000.ethernet3: device MAC address ae:dd:63:2f:3d:9a [ 7.204420] dwc-eth-dwmac 9090000.ethernet3: Enabled Flow TC (entries=4) [ 7.211089] dwc-eth-dwmac 9090000.ethernet3: TSO feature enabled [ 7.217066] dwc-eth-dwmac 9090000.ethernet3: Using 40 bits DMA width [ 7.266909] vir_addr = ffffffc018701000 phy_addr = 00000000f6000000 [ 7.273151] vir_addr_0 = ffffffc01a701000 [ 7.277150] misc loadelf_driver: ucp_2_revem_module_init ok [ 7.309790] spinlock init success! [ 7.326512] ucp_sm_ddr_cache_module_init ok cat /sys/devices/virtual/misc/ucp_sm_ddr_cache [ 7.335108] ucp_sm_ddr_noncache_module_init ok cat /sys/devices/virtual/misc/ucp_sm_ddr_noncache [ 7.344333] globle g_vir_ecs_sm_cache_add = 0xffffffc01a880000 [ 7.344335] globle g_vir_pet_sm_cache_add = 0xffffffc01a900000 [ 7.351784] globle g_vir_share_sm_cache_add = 0xffffffc01b000000 [ 7.359233] globle g_vir_msg_cache_add = 0xffffffc020000000 [ 7.366856] globle g_vir_stack_cache_add = 0xffffffc040000000 [ 7.416879] bsp_init. [ 7.434113] bsp module init success! [ 7.459250] misc mem_export: mem_export module_init ok [ 7.478219] ioreg_module_init ok [ 7.489355] enter:smartlogic_stc_probe [ 7.508058] CPU:2 [ 7.508059] CPU:3 [ 7.508061] CPU:1 [ 7.508064] CPU:6 [ 7.508066] CPU:7 [ 7.508067] CPU:5 [ 7.508069] CPU:4 [ 7.528874] CPU:0 [ 7.532346] Enable Access PMU Initialized [ 7.597192] dwc-eth-dwmac 1a40000.ethernet0 eth0: PHY [stmmac-0:00] driver [Marvell 88E1510] (irq=POLL) [ 7.621082] dwmac4: Master AXI performs any burst length [ 7.626376] dwc-eth-dwmac 1a40000.ethernet0 eth0: No Safety Features support found [ 7.633915] dwc-eth-dwmac 1a40000.ethernet0 eth0: No MAC Management Counters available [ 7.641799] dwc-eth-dwmac 1a40000.ethernet0 eth0: IEEE 1588-2008 Advanced Timestamp supported [ 7.651334] dwc-eth-dwmac 1a40000.ethernet0 eth0: registered PTP clock [ 7.661158] dwc-eth-dwmac 1a40000.ethernet0 eth0: configuring for phy/rgmii link mode [ 7.802192] dwc-eth-dwmac 1a40000.ethernet0 eth0: PHY [stmmac-0:00] driver [Marvell 88E1510] (irq=POLL) [ 7.821082] dwmac4: Master AXI performs any burst length [ 7.826377] dwc-eth-dwmac 1a40000.ethernet0 eth0: No Safety Features support found [ 7.833916] dwc-eth-dwmac 1a40000.ethernet0 eth0: No MAC Management Counters available [ 7.841801] dwc-eth-dwmac 1a40000.ethernet0 eth0: IEEE 1588-2008 Advanced Timestamp supported [ 7.851328] dwc-eth-dwmac 1a40000.ethernet0 eth0: registered PTP clock [ 7.857840] dwc-eth-dwmac 1a40000.ethernet0 eth0: configuring for phy/rgmii link mode [ 7.890956] dwc-eth-dwmac 9090000.ethernet3 eth2: No Safety Features support found [ 7.898509] dwc-eth-dwmac 9090000.ethernet3 eth2: IEEE 1588-2008 Advanced Timestamp supported [ 7.907870] dwc-eth-dwmac 9090000.ethernet3 eth2: registered PTP clock [ 7.917648] dwc-eth-dwmac 9090000.ethernet3 eth2: configuring for inband/xlgmii link mode [ 10.633086] dwc-eth-dwmac 9090000.ethernet3: PET pma3 lane0 receiver adapt req ack[15:8]:c6 limit:45 [ 10.642265] dwc-eth-dwmac 9090000.ethernet3: PMA rx valid ok [ 10.647904] dwc-eth-dwmac 9090000.ethernet3: PMA training ok [ 11.042028] dwc-eth-dwmac 1a40000.ethernet0 eth0: tx rate = 125000000 [ 11.050509] dwc-eth-dwmac 1a40000.ethernet0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 11.809088] dwc-eth-dwmac 9090000.ethernet3: PCS state ok [ 11.814478] dwc-eth-dwmac 9090000.ethernet3 eth2: Link is Up - 10Gbps/Full - flow control off [ 11.823711] dwc-eth-dwmac 9090000.ethernet3 eth2: Link is Down [ 11.834019] dwc-eth-dwmac 9090000.ethernet3 eth2: No Safety Features support found [ 11.841571] dwc-eth-dwmac 9090000.ethernet3 eth2: IEEE 1588-2008 Advanced Timestamp supported [ 11.850915] dwc-eth-dwmac 9090000.ethernet3 eth2: registered PTP clock [ 11.857439] dwc-eth-dwmac 9090000.ethernet3 eth2: configuring for inband/xlgmii link mode [ 14.465090] dwc-eth-dwmac 9090000.ethernet3: PET pma3 lane0 receiver adapt req ack[15:8]:c9 limit:45 [ 14.474269] dwc-eth-dwmac 9090000.ethernet3: PMA rx valid ok [ 14.479907] dwc-eth-dwmac 9090000.ethernet3: PMA training ok [ 25.000189] sh (644): drop_caches: 3 [ 35.011524] enter ucp_sm_ddr_noncache_open [ 35.015644] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0xa8000000,vm_start = 0x7ec4000000 [ 35.031728] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0x9d00000,vm_start = 0x7ee03ff000 [ 35.039665] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0x9400000,vm_start = 0x7edb800000 [ 35.047897] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0x7200000,vm_start = 0x7ee8500000 [ 35.055927] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0x8700000,vm_start = 0x7ee84a0000 [ 35.063952] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0x10000000,vm_start = 0x7e38000000 [ 35.075032] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0x9c000000,vm_start = 0x7e34000000 [ 35.083357] enter ucp_sm_ddr_noncache_mmap,phyaddr = 0xa0000000,vm_start = 0x7e2c000000 [ 35.091510] enter ucp_sm_ddr_cache_open [ 35.095611] enter ucp_sm_ddr_cache_mmap,phyaddr = 0x100000000,vm_start = 0x7d2c000000 [ 35.108626] dwc-eth-dwmac 9090000.ethernet3: PCS state ok [ 35.114062] dwc-eth-dwmac 9090000.ethernet3 eth2: Failed to pcs link up [ 35.120671] dwc-eth-dwmac 9090000.ethernet3 eth2: Link is Up - 10Gbps/Full - flow control off