项目

一般

简介

错误 #3167

[3.0产品测试]3.0.1pre1_T3 小区激活失败，DU产出系列报错后return

由 刘 抒放 在 20 天 之前添加. 更新于 14 天 之前.

状态:
已解决
优先级:
普通
指派给:
赵 晓辉
开始日期:
2025-04-16
计划完成日期:
% 完成:

0%

预期时间:
问题归属:
DU, 系统
发现问题版本:
Rel_3.0.1
目标解决问题版本:
Rel_3.0.1

描述

测试设备：192.168.8.163 基站板卡+兴悦达3.5G功放整机
问题现象：升级3.0.1Pre1_T3后，小区激活du侧显示如图错误后return出来。同配置T2可激活。
报错如下：
ldconfig: /lib/libatomic.so.1 is not a symboliclink
ldconfig: /lib/libatomic_ops_gpl.so.1 is not a symbolic link
ldconfig: /lib/libpcre.so.1 is not a symbolic link
ldconfig: /lib/libsysrepo.so.5 is not a symboliclink
ldconfig: /lib/libatomic_ops.so.1 is not a symbolic link
ldconfig: /lib/libxml2.so.2 is not a symbollic link
ldconfig: /lib/libyang.so.1 is not a symbollic link
rm: cannot remove 'msgdump*': No such file or directorTy
rm: cannot remove 'du_dbg_log*': No such file or diredtory
rm: cannot remove 'du_mem_log*': No such file or diredtory
!! sysrepo_start OAM_AGENT_READ_CONFIG_STARTED
[INF]: Scheduled changes not applied because of otherexisting connections.
[INF]: Connection 2 created.
[INF]: Session 43 (user "root", CID 2) created.
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRRU_TX_FREQ = 3350820000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_RXFREQ = 3350820000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_AUXFREQ =
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_TX_MAX_POWER = 430
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_RX_GAIN = 255
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_SAWIPLE_RATE = 122880000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_VWIDEBAND = 100000000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PPRU_TX_ANTNUMBER = 4
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRUTRANS_MODE = 0
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PPRU_ORX_ENABLE = 0
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_204C_ENABLE = 0
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PRU_UCCPIOG_ENABLE = 0
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PA_FREQ = 600000000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PACHANNEL = 17
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PA_CHANNEL_ATT1 = 150000000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PA_CHAANNEL ATT2 = 14500000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PA_CHAANNEL ATT3 = 14500000
get_cell_config /du-cell:DU-CELL/PRU_CONFIG/NR_CELL_PAA_CHANNEL_ATT4 = 16450000
gen_running_rfic_cfg_file_path: load file error!

历史记录

#1

由 刘 抒放 更新于 20 天 之前

研发已定位，需替换board.cfg文件进入firemware文件夹中，此单待T4升级后无问题则关闭

#2

由 周 立伟 更新于 14 天 之前

  • 状态 从 新建 变更为 已解决

将board.cfg文件放到了phy文件下，下个版本T4生效。已验证通过

导出 Atom PDF